Robroy Industries Releases PVC Coating Repair Kit

Robroy Industries

The new repair kit allows for superior restoration of coatings if damage occurs in the field

Gilmer, TX - Robroy Industries, a manufacturer of electrical products including PVC-coated conduit, fittings, and accessories has released a new PVC Coating Repair Kit to mend coating damage that may occur in the field after product is installed.  This Repair Kit differs from their traditional PVC touch-up compound as it is formulated to adhere to bare metal unlike the touch-up compound.

The primary function of a PVC-coated conduit system is to maximize the life of the electrical system contained within it and to prevent corrosion from sabotaging its structural integrity. This is achieved through a PVC coating properly adhered to the external surface of the conduit and fittings, preventing exposure to external environmental conditions that could result in corrosion of the steel or aluminum substrate.
 
Preventative Measures
A variety of solutions exist to prevent the occurrence of damage to PVC-coated conduit systems. Robroy offers complimentary installation training and certification based on classroom instruction, hands-on instruction, and online tutorials. Through the utilization of proper tools and methods during the installation process the product will perform as designed by the manufacturer.  

Disaster Strikes
However, damage is possible due to accidents - even with trained personnel. Bundles of heavy conduit can be dropped onto hard, pointed surfaces; construction equipment and tools can fall or run into a system. In these cases, a method of repair is inevitable. As a result, PVC-coated manufacturers have developed products to easily patch minor defects to the factory-applied coatings.

Damage Control
Robroy currently offers a PVC Touchup Compound and Touchup Spray to repair minor damages to the surface of the PVC coating. However these compounds are not formulated nor are they intended to bond to the metal substrate when the damage penetrates the coating and exposes the metal substrate. For these cases, a PVC Coating Repair Kit was developed using a custom formulated UL recognized two part epoxy capable of bonding to both polyvinyl chlorides and steel or aluminum substrates. 

The repair kit includes all tools needed to prepare a small surface prior to applying the epoxy patch. This includes an emory cloth to prepare the surface of the damaged area, mixing tools, cleaning cloths, an applicator tool, instruction sheet, and chemical information (SDS) for the compound. The PVC Coating Repair Kit uses a two-part epoxy cold weld system that provides strong, lasting repairs to metal and PVC. After mixing, it forms a permanent bond that can be shaped, tapped, filed, and sanded after curing. The PVC Coating Repair Kit epoxy sets in 6 minutes and cures in 3-4 hours (at 70⁰F) to a dark grey color that matches Robroy’s PVC coating. This epoxy is a UL recognized performance material that has been tested for flame resistance according to UL’s HB Flammability test for safety assurance.


Performance properties are detailed in Table 1 below:

Property                                 Rating
Flame Resistance                     HB Rating – self-extinguishing
Tensile Strength                      3960 psi
Heat Resistance                       550⁰F - No change after cooling
Freeze Resistance                    -67⁰F – No change after thawed
Hardness                                 2H-4H pencil (ASTM D2240)
Adhesion                                Pull Test - Pass
Conductivity                            This material is an insulator

Once the epoxy is completely cured, it is resistant to water, gasoline, and other petroleum products. It is important to note that the kit is only for use in the case of small repairs caused by unavoidable damage to PVC conduit systems. It should not be used to repair damaged areas with a surface area greater than 4 in2.

The PVC Coating Repair Kit is available for purchase.  Additional information and cut sheets are also available on the PVC-coated product website which can be found at www.robroy.com.  

About Robroy Industries Raceway Division: Robroy Industries is a manufacturer of electrical products and has been in one-family ownership for over 110 years.  The Raceway Division manufactures a complete line of PVC Coated Conduit, Fittings, and Accessories for use in corrosive environments.  Manufactured in the U.S.A., ISO 9001-certified, the PVC coated line complies with all standards mandated by UL6, UL 1203, NEMA RN-1, ANSI C80.1 and ETL PVC-001.  For more information, visit: www.robroy.com

Welcome to ElectricSmarts

You're in good company!
More than 225,000 electrical professionals use ElectricSmarts to access our eCatalog of 2 million plus products, the latest new product information, videos, spec sheets and more.
Email:
We care about your privacy, see our privacy policy.